Kinetics Fitting Software
# kfits Kinetics Fitting Software
This software package was written by Oded Rimon, at Dr. Dana Reichmann’s Lab, HUJI, Israel.
The Lab is Located at: Dept. of Biological Chemistry, room 1-626 The Alexander Silberman Institute of Life Science The Hebrew University of Jerusalem Givat Ram Campus, Jerusalem, 91904, Israel Tel: (+972) 2-658-5703
Email us at: Oded: oded.rimon AT mail.huji.ac.il Dana: danare AT mail.huji.ac.il
# Installation Instructions
Executive Summary: pip install kfits
## 1 Get Python 2.7
If you already have Python 2 (2.6 or later, but not 3.x) installed, skip to step 2. If you have both Python 2 and Python 3 installed, that’s fine too. If you’re working on a linux system, chances are you already have Python 2.7 installed. Otherwise, follow the instructions on [this official download page](https://www.python.org/downloads/) to download and install Python 2.7. Note that Python 3 will not work for this software, so don’t be tempted ;) For Windows and MacOS, you may choose to work with [ActiveState ActivePython](https://www.activestate.com/activepython/downloads) or another distribution. As long as it’s python 2.7, it’s fine.
## 2 Install pip - the python package installer If you are certain you have pip installed, you may skip to step 3. Otherwise, follow the instructions on the [pip installation page](https://pip.pypa.io/en/stable/installing/). Shortly, depending on your system, it should be as easy as running (Fedora <22): ` sudo yum upgrade python-setuptools sudo yum install python-pip python-wheel ` Or (Fedora >=22): ` sudo dnf upgrade python-setuptools sudo dnf install python-pip python-wheel `` Or (Debian / Ubuntu): ` sudo apt-get install python-pip ` Or (Windows or any other system): Download [get_pip.py](https://bootstrap.pypa.io/get-pip.py) and run python get_pip.py in the folder you downloaded it to.
## 3 Get the numerical (NumPy) and scientific (SciPy) python packages Depending on your specific system, environment and sheer luck, this step may be smooth and easy or long and tedious. We sincerely apologise if the latter applies to you - unfortunately it is out of our hands (we even tried to rewrite the code without any use of scipy, but it is just so darn useful..!). First, check if you already have scipy. Open a python terminal (either IDLE or by simply typing python in a command line window) and try: import scipy. If no error message was presented - you’re in luck! Skip to step 4! No luck..?
### 3.1 Install NumPy Well, this is where things start to get a bit complicated. There are many ways to install NumPy, and frankly I haven’t seen one that works on all systems. If you’re working on a linux or linux-based system, the best way IMHO is using pip install numpy. However, you will first need to install python-dev, liblapack-dev and gfortran, and if you don’t have a suitable C/C++ compiler installed, you would need one of those as well. For me, on an Ubuntu system, the following two commands were sufficient: ` sudo apt-get install python-dev liblapack-dev gfortran sudo pip install numpy ` However, your results may vary (and if you’re using another linux distribution, remember to replace apt-get install with the appropriate installation command, e.g. yum install). On a Windows system, you may prefer to download pre-compiled NumPy from [this University of California page](http://www.lfd.uci.edu/~gohlke/pythonlibs/) and follow the instructions there; or you may choose to install [Visual C++ for Python 2.7](http://www.microsoft.com/en-us/download/details.aspx?id=44266) and use pip install numpy as you would on linux-based systems. Once you chose your method and you think you have NumPy installed, open a python terminal and type import numpy. If no error message appears - you’re finally done with this step, and almost ready to install _Kfits_ :)
### 3.2 Install SciPy Once you successfuly installed numpy, installing scipy should be a piece of cake. Whatever was your last step for installing numpy (e.g. pip install numpy or downloading from [the unofficial binaries page](http://www.lfd.uci.edu/~gohlke/pythonlibs/)) - do exactly the same for scipy. Once you have scipy successfully installed, you should be able to type in import scipy in a python terminal and receive no error messages when you press ENTER.
## 4 Download and Install Kfits Finally, everything is prepared and you can download and install Kfits. There is more than one way to do this, and you may choose whichever you prefer. We think the first is the simplest and most straight-forward method, but really, feel free to use others. We won’t be offended. Really.
### Via pip ` pip install kfits ` Seriously. That’s it.
### From source You can download the source code of Kfits from [github](https://github.com/odedrim/kfits). Either clone it with git (go to a directory of your choice, type in git clone https://github.com/odedrim/kfits, and you’ll have a subdirectory named kfits containing the source code) or download as ZIP and unzip it to a directory of your choice. Once you have a directory which contains the source code of kfits, change dir (cd) to that directory and type python setup.py install or sudo python setup.py install (to install with root privileges on a linux-based system)… And you’re done.
### Precompiled Packacges (binary distributions) We will do our best to precompile binary packages for as many operating systems and environments as we can - but eventually we are just Biochemists in the academy, we don’t really have access to that many different systems. The binary distributions will be made available at [github](https://github.com/odedrim/kfits), in the [install directory](https://github.com/odedrim/kfits/tree/master/install). To install them, simply download the one best suited to your setup, and double click / run it to install.